Skip to content
Serving Livermore and nearby cities Mon–Fri: 8 AM–8 PM · Requests accepted 24/7 · (650) 203-2763

Heating Repair in Dublin, CA

Serving Dublin and nearby cities. Tell us about the job and we’ll call you back to confirm the details.

Tell us what’s going on

Prefer to talk? (650) 203-2763

The short answer

TotalFlow HVAC Repair Service fixes furnaces and heat pumps in Dublin, CA, starting with a diagnosis that tells you what failed and why. Bay Area Air District rules don't make you replace a working furnace, so repair is often the right first step. If replacement does make sense, we'll explain your options before you decide anything.

When your heat stops working on a cold Dublin evening, you want a clear answer about what failed and what it will take to fix it. TotalFlow HVAC Repair Service is based in Livermore, about 6 miles east of Dublin. We repair gas furnaces, heat pumps and the controls and ductwork that connect them in homes throughout the 94568 ZIP code. On this page you'll find the problems we see most, what to expect when we come out, some checks you can safely do first, and how current Bay Area rules affect the choice between repairing and replacing.

Heating problems we see in Dublin homes

Most homes in Dublin heat with a gas furnace, a heat pump, or a combination of the two. Many of these systems run only part of the year, so problems tend to show up in the first cold weeks of fall, when the system starts working hard again after months of sitting idle.

These are the issues we're called about most often:

  • Furnace runs but blows cool or lukewarm air
  • Burners light, then shut off after a few seconds
  • System won't start at all, or the thermostat screen is blank
  • Heat pump runs constantly but the house never reaches the set temperature
  • Banging, squealing, grinding or rattling noises when the blower starts
  • Some rooms stay cold while others overheat
  • Short cycling, where the system turns on and off every few minutes
  • A burning or electrical smell that doesn't fade after the first run of the season

What happens during a repair visit

We start by asking what you've noticed: when the problem began, whether it comes and goes, and any sounds or smells. Then we test the system in operation. On a gas furnace, that includes the ignition sequence, flame sensor, safety switches, pressure switch, blower motor, capacitor and control board. On a heat pump, we check the refrigerant circuit, the defrost cycle, the reversing valve, the outdoor fan and the backup heat strips.

Once we find the cause, we explain it in plain terms and lay out your options before any work begins. If a part is worn but still working, we'll say so and let you decide whether to replace it now or keep an eye on it. When the repair is finished, we run the system through a full heating cycle to confirm it's working as it should.

Repair or replace? What Bay Area rules mean for you

If you own an older furnace, you may have heard about new Bay Area Air District rules. Under Rule 9-4, natural gas furnaces manufactured from 2029 on must meet a zero-NOx emission standard. In practice, that points homeowners toward heat pumps when they replace a furnace after that date.

Those rules do not require you to replace equipment that still works. They apply only when an existing furnace fails or is replaced. If your furnace can be repaired safely and for a reasonable cost, fixing it is a perfectly sound choice. We'll tell you honestly when a system is near the end of its useful life, so you can plan a replacement on your own schedule instead of during an emergency.

If you are thinking about switching to a heat pump, note that the federal 25C tax credit ended for systems placed in service after December 31, 2025. Local help may still be available. You can check BayREN and your local clean energy provider for current heat pump and electrification incentives. Amounts and availability change with each funding cycle, so we confirm the current offer before we include it in any quote.

Heat pump repair in Dublin

More Dublin homeowners are running heat pumps, and these systems fail differently than furnaces. A heat pump that ices over and doesn't clear, blows cool air in heating mode, or leans heavily on its backup heat strips usually has a problem with its defrost controls, its refrigerant charge or its reversing valve. Running a struggling heat pump on backup heat for weeks can sharply raise your electric bill. It's worth having the system checked instead of living with it.

Safe checks to try before you call

A few simple checks can sometimes get your heat back on without a service visit, or help us diagnose the problem faster if we do come out:

  • Make sure the thermostat is set to Heat and set a few degrees above room temperature, and replace its batteries if it uses them
  • Check the breaker for the furnace or air handler, and the power switch near the unit, which often looks like a light switch
  • Replace a dirty air filter, since a clogged filter can cause overheating and shutdowns
  • Confirm the furnace access panel is fully closed, because a safety switch keeps the unit off when it's open
  • Keep the outdoor heat pump unit clear of leaves and debris

More services in Dublin

Related

What to expect

How a visit goes

  1. Find the cause first

    We test and inspect before recommending parts or equipment, so the fix matches the actual problem instead of a guess.

  2. Clear options, no pressure

    When a system could be repaired or replaced, we lay out both paths and the tradeoffs, then let you decide what fits your home.

  3. Current information on rules and incentives

    Air District rules and rebate programs change. We confirm what applies today before we talk about it, so you can plan with accurate information.

FAQ

Common questions

Do you provide heating repair throughout Dublin?

Yes. We serve homes across Dublin's 94568 ZIP code from our base in Livermore, about 6 miles away. We also work in Pleasanton, San Ramon, Danville, Union City and Hayward.

Will I have to replace my gas furnace because of the new Air District rules?

No. The Bay Area Air District rules don't require replacing working equipment. They apply only when a furnace fails or is replaced. The zero-NOx standard covers gas furnaces manufactured from 2029 on.

Should I repair my furnace or replace it?

It depends on the furnace's age and condition, how much the repair involves, and how often the furnace has needed service recently. We'll explain what we find and give you both options so you can decide.

Can I still get a federal tax credit for a new heat pump?

Not the federal 25C credit. It covered qualifying heat pumps placed in service before December 31, 2025. Check BayREN and your local clean energy provider for current incentives, which change with each funding cycle.

What should I do if I smell gas?

Leave the house right away and don't operate switches or appliances. Once you're outside, call your gas utility or 911. Schedule a heating repair only after the utility has made the home safe.

Why does my heat pump blow cool air in heating mode?

Common causes include a defrost cycle that isn't working properly, a low refrigerant charge, a failing reversing valve, or a thermostat setup problem. We test each of these to find the actual cause.

Need Heating or Cooling Help in Livermore?

Tell us what your system is doing, or not doing, and we'll schedule a visit to find the cause and walk you through your options.

(650) 203-2763
Call (650) 203-2763 Request Service