Skip to content
Serving Livermore and nearby cities Mon–Fri: 8 AM–8 PM · Requests accepted 24/7 · (650) 203-2763

AC Installation in Danville, CA

Serving Danville and nearby cities. Tell us about the job and we’ll call you back to confirm the details.

Tell us what’s going on

Prefer to talk? (650) 203-2763

The short answer

TotalFlow installs central air conditioners and heat pumps in Danville homes. We start with a load calculation and a duct check so the system fits your house. Many homeowners compare a heat pump with a standard AC, especially if their furnace is aging.

If your Danville home has never had central air, or the system you have is struggling through warm afternoons, a new installation is a chance to get comfort right. TotalFlow HVAC Repair Service installs central air conditioners and heat pumps for homeowners in Danville (ZIP 94526) and across Contra Costa County. We're based in Livermore, about 13 miles southeast, so getting to your home for an estimate or install day is straightforward. This page covers how we size and plan a new system, what to consider before choosing equipment, and what incentives are actually available right now.

Sizing a New AC for Your Danville Home

The most common problem we see with air conditioning is a system that was sized by guesswork. An oversized unit cools the air fast, shuts off, and starts again a few minutes later. That short-cycling wears out parts, leaves rooms clammy, and creates uneven temperatures. An undersized unit runs nonstop on hot days and still can't keep up.

Before we recommend any equipment, we run a load calculation based on your actual house. Danville is inland, away from the Bay's cooling breezes, so afternoon heat matters more here than it does closer to the water.

  • Square footage and ceiling height
  • Window size, orientation, and shading
  • Attic insulation and air sealing
  • Which rooms get afternoon sun
  • How many people live in the home and how you use each space

Checking Your Ductwork Before Installation

A new air conditioner can only perform as well as the ducts that carry its air. In older homes, ducts often have loose joints, crushed sections in the attic, or runs that were sized for heating only. If your home had a furnace but no AC, the existing ducts may be too small to move the volume of air that cooling needs.

We inspect the duct system as part of every installation estimate. Sometimes the ducts are fine as they are. Sometimes they need sealing, a few new runs, or a return air upgrade. We'll show you what we found and explain which changes affect comfort and which are optional.

Central AC or Heat Pump: Choosing for the Long Term

A heat pump looks and installs much like a central air conditioner, but it can also heat your home by running in reverse. For many Danville homeowners, the decision comes down to the age and condition of the furnace.

Under Bay Area Air District Rule 9-4, natural gas furnaces made starting in 2029 must meet a zero-NOx emission standard. In practice, that points homeowners toward heat pumps when they replace a furnace after that date. The rule does not require you to replace working equipment. It applies only when an existing furnace fails or is replaced.

If your furnace is in good shape, adding a standard AC coil and condenser can make sense. If your furnace is nearing the end of its life, a heat pump that handles both heating and cooling may save you from doing two projects a few years apart. We'll walk through both options with you.

What to Know About Incentives Right Now

The federal Energy Efficient Home Improvement Credit (25C) covered qualifying heat pumps placed in service before December 31, 2025. It is not available for new installations after that date, so don't count on it when budgeting a project today.

Bay Area homeowners can still check BayREN and their local clean energy provider for heat pump and electrification incentives. Amounts and availability change with each funding cycle. We confirm the current offer before including it in any quote, so you aren't planning around money that is no longer available.

What Happens on Installation Day

Once you approve the plan, we schedule the install and explain what to expect, including whether we need attic access, side-yard access, or a new electrical circuit.

On install day, the crew protects floors and work areas, removes old equipment if there is any, sets the outdoor unit on a level pad, and installs the indoor coil or air handler. Then we connect the refrigerant lines, electrical, and condensate drain. Before we leave, we start the system, check refrigerant charge and airflow, confirm the thermostat works correctly, and show you how to change the filter.

  • Load calculation and duct inspection
  • Equipment selection: central AC or heat pump
  • Clean installation with old equipment removed
  • Startup testing, airflow, and charge verification
  • Walkthrough of thermostat settings and filter care

More services in Danville

Related

What to expect

How a visit goes

  1. Find the cause first

    We test and inspect before recommending parts or equipment, so the fix matches the actual problem instead of a guess.

  2. Clear options, no pressure

    When a system could be repaired or replaced, we lay out both paths and the tradeoffs, then let you decide what fits your home.

  3. Current information on rules and incentives

    Air District rules and rebate programs change. We confirm what applies today before we talk about it, so you can plan with accurate information.

FAQ

Common questions

How long does an AC installation take in a Danville home?

Replacing an existing system usually takes one day. Adding central air to a home that never had it, or making duct changes, can take longer. We give you a time estimate after the in-home visit.

Can you add central air if my home only has a furnace?

Usually, yes. We add a cooling coil and an outdoor unit, and we check whether your ducts can handle cooling airflow. Some homes need duct changes first.

Do I have to replace my gas furnace because of the new Air District rules?

No. The Bay Area Air District rules don't require replacing working equipment. They apply only when an existing furnace fails or is replaced.

Can I still get the federal tax credit for a heat pump?

No. The federal 25C credit covered qualifying heat pumps placed in service before December 31, 2025, and it doesn't apply to new installations after that date.

Are there local incentives for heat pumps in Danville?

Check BayREN and your local clean energy provider. Offers change by funding cycle, and we confirm what's currently available before quoting it.

Do you serve areas near Danville?

Yes. Along with Danville, we install AC systems in San Ramon, Dublin, Clayton, Pleasanton, and Union City.

Need Heating or Cooling Help in Livermore?

Tell us what your system is doing, or not doing, and we'll schedule a visit to find the cause and walk you through your options.

(650) 203-2763
Call (650) 203-2763 Request Service