Skip to content
Serving Livermore and nearby cities Mon–Fri: 8 AM–8 PM · Requests accepted 24/7 · (650) 203-2763

Heating Repair in Danville, CA

Serving Danville and nearby cities. Tell us about the job and we’ll call you back to confirm the details.

Tell us what’s going on

Prefer to talk? (650) 203-2763

The short answer

TotalFlow HVAC Repair Service repairs gas furnaces, heat pumps, and heating controls in Danville homes (ZIP 94526). Bay Area Air District rules do not require you to replace a working furnace, so repairing a sound system is a reasonable choice. If replacement does come up, we explain how the zero-NOx furnace standard for units made from 2029 and current local incentives may affect your options.

When the heat stops working in a Danville home, you need to know what failed, what it takes to fix it, and whether repair still makes sense. TotalFlow HVAC Repair Service handles heating repair for homes in Danville (ZIP 94526), about 13 miles northwest of our Livermore base. We work on gas furnaces, heat pumps, and the thermostats, ducts, and controls that connect them. Below is what to check before you call, what we look for once we arrive, and how current Bay Area Air District rules affect the repair-or-replace decision.

Heating Problems We See in Danville Homes

Most heating calls in Danville start on the first cold mornings of the season, when a system that sat idle all summer is asked to run for hours. Parts that wore slowly the previous winter tend to fail at that point. Some homes have a single furnace in a garage, attic, or hall closet. Others have two systems or a heat pump paired with a gas furnace, and each setup fails in its own way.

These are the problems homeowners describe most often:

  • Furnace blower runs but the air from the vents stays cold
  • Burners light, then shut off after a few seconds
  • System will not start at all, or the thermostat screen is blank
  • Heat pump runs constantly but the house never reaches the set temperature
  • Some rooms stay cold while others overheat, often on an upper floor
  • New noises when the system starts: banging, squealing, or rattling
  • A burning or electrical smell that continues past the first few minutes of the season

What to Check Before You Call

A few simple checks can save you a visit or help us diagnose the problem faster. Confirm the thermostat is set to heat and the setpoint is above the room temperature. Replace thermostat batteries if the display is dim or blank. Check the breaker for the furnace or air handler, and make sure the service switch near the unit, which often looks like a light switch, is on.

Look at the air filter. A clogged filter can make a furnace overheat and shut itself off, and it can cause a heat pump to struggle. If the furnace door panel is loose, the safety switch behind it may keep the system off. If you smell gas, leave the house and call your gas utility from outside before calling anyone else.

How We Diagnose and Repair Your System

We start by watching the system run through a full heating cycle and reading any error codes on the furnace control board or heat pump. From there we test the parts most likely to cause the symptom you described: the igniter, flame sensor, pressure switches, inducer motor, blower motor and capacitor, limit switches, and gas valve on a furnace; the reversing valve, defrost controls, outdoor fan, and refrigerant operation on a heat pump.

We also check the parts outside the equipment itself. Loose or crushed ductwork in an attic or crawlspace can leave rooms cold even when the furnace works fine. Thermostat wiring problems can mimic a failed control board. Once we find the cause, we explain what failed, what the repair involves, and anything else we noticed that is likely to cause trouble soon, so you can decide what to do.

Repair or Replace? What Bay Area Rules Mean for You

Many Danville homeowners ask whether new air quality rules mean they should replace their furnace now. They do not. The Bay Area Air District appliance rules do not require replacing working equipment. They apply only when an existing furnace or water heater fails or is replaced. If your furnace can be repaired safely and reliably, repair is a sound option.

Looking further ahead, gas furnaces manufactured from 2029 must meet a zero-NOx emission standard. In practice, that points homeowners toward heat pumps when a furnace is replaced after that date. If your furnace is aging and needs frequent repairs, it is worth weighing that timeline when you consider a major repair versus planning for a heat pump. We will lay out both paths plainly and leave the decision to you.

Incentives and Tax Credits: What Is Current

The federal Energy Efficient Home Improvement Credit (25C) covered qualifying heat pumps placed in service before December 31, 2025. It is not available for heat pumps installed after that date, so plan without it.

Bay Area homeowners can still check BayREN and their local clean energy provider for current heat pump and electrification incentives. Amounts and availability change by funding cycle, so we confirm the current offer before we quote it to you. If you are also thinking about a water heater, the zero-NOx date for small water heaters was set for 2027, and the Air District Board is considering amendments in November 2026 that could delay it. Check the current rule before you plan that replacement.

More services in Danville

Related

What to expect

How a visit goes

  1. Find the cause first

    We test and inspect before recommending parts or equipment, so the fix matches the actual problem instead of a guess.

  2. Clear options, no pressure

    When a system could be repaired or replaced, we lay out both paths and the tradeoffs, then let you decide what fits your home.

  3. Current information on rules and incentives

    Air District rules and rebate programs change. We confirm what applies today before we talk about it, so you can plan with accurate information.

FAQ

Common questions

Do you provide heating repair throughout Danville?

Yes. We serve homes across Danville, ZIP 94526, from our base in Livermore about 13 miles away. We also serve San Ramon, Dublin, Clayton, Pleasanton, and Union City.

Do I have to replace my gas furnace because of the new Bay Area rules?

No. The Bay Area Air District rules do not require replacing working equipment. They apply only when an existing furnace fails or is replaced, so a repairable furnace can stay in service.

What changes in 2029 for furnaces?

Gas furnaces manufactured from 2029 must meet a zero-NOx emission standard. In practice, that steers replacements after that date toward heat pumps. It does not affect a furnace you already have and keep repairing.

Can I still get the federal tax credit for a heat pump?

No. The federal 25C credit covered qualifying heat pumps placed in service before December 31, 2025, and it is not available for installations after that date. Check BayREN and your local clean energy provider for current incentives instead.

Do you repair heat pumps as well as furnaces?

Yes. We diagnose and repair heat pumps, gas furnaces, and dual-fuel systems that pair the two, along with the thermostats, controls, and ductwork connected to them.

Why are some rooms in my house cold while others are warm?

Common causes include leaking or disconnected ducts, closed or blocked vents, a dirty filter, a weak blower, or one system trying to heat more than one floor. We check both the equipment and the duct system to find the cause.

Need Heating or Cooling Help in Livermore?

Tell us what your system is doing, or not doing, and we'll schedule a visit to find the cause and walk you through your options.

(650) 203-2763
Call (650) 203-2763 Request Service